Tongue-and-Groove Siding If your home has wood tongue-and-groove boards, here's a list of what you'll need to remove and replace the old sections. Tongue-and-groove siding tool list: Protective go
May 17, 2017 . For this repair project we milled interlocking tongue-and-groove boards from treated lumber to replace the original rotted porch boards. I decided to replace .. I also strongly recommend removing the old flooring and installing new flooring up to a point that is near to each column to be jacked-up. Since the..
Nov 1, 2008 . Because tongue-and-groove products like the decking shown above may drain surface water slowly, it's important to ensure the framing is flat to avoid ponding. The biggest challenge when installing new deck boards over old joists is making sure that the joists crown the same way. To avoid visible bumps..
Deck-Repair Tips. Inspect your deck frequently for popped nails and loose railings or boards. Remove and replace any nails that have popped with coated screws, and immediately repair or replace loose . Set the first board in tongue first, and insert each board to lock its tongue into the groove of the previous board
Jul 1, 1999 . I installed tongue-and-groove decking on my porch, and as a consequence, I had to use other clamping methods to d the boards together. I used the rim joist as the bearing point . Then I used a grinder to remove a bit of the webbing from the back of the screw clamp. This created a flat bearing spot that..
installation Keep a copy for your records As you enjoy your Perennial Wood porch, always abide by . Wood products. Although Perennial Wood has very good dimensional stability, tongue-and-groove porch flooring should always be installed to allow for potential . removing packaging and adding space between each
Take a pry bar to remove the nails and screws that hold the tongue and groove deck boards in place. Remove each of the damaged deck boards that need to be replaced. Check the joists underneath the deck boards for any damage as well. The joists are the boards, which the deck boards are attached. Any damaged joists..
The technology inside each board allows the flooring to be lightweight, but with a fiber-like structure inside, similar to wood, it has unmatched strength. The lightweight porch flooring is easy-to-handle on the job site and won't splinter, sag, chalk or crack unlike other porch flooring options. Available in tongue-and-groove and..
Installation Guidelines. AZEK Porch should be installed using the same good building principals used to install wood or composite porch and in accordance with the local building codes and the installation guidelines included below. AZEK Building Products. Inc. accepts no liability or responsibility for the improper..
Use a hammer and wood chisel to remove the first rotten board, being careful not to damage the tongue or groove of the sound board next to it. Once you have the first board out, use a cat's paw or pry bar to take out any other damaged pieces. Before putting down the replacement flooring, look carefully at the wood frame..
Dec 6, 2014 . With some care and patience, more than 90% of my pine flooring was removed with so little damage that the planks were in good enough condition to reinstall, ..
Mar 28, 2017 . Read some of the latest reviews for Zimmerman Construction and Roofing out of Montville Connecticut. This shows some of our latest customers jobs by location and their reviews. Call us if you have any requests we can probably send you more. We do anything exterior like roofing, siding Fences and..
Dec 27, 2010 . The first step in removing tongue and groove material, whether it is on a floor or a wall, is to find a starting place. Basically, this involves destroying one board. If the porch or other floor or the siding is rotted, that may give you a starting point. But you have to remove one whole board first to gain access to..
Feb 11, 2011 . When Ted assembles a porch deck, he begins and ends with a special technique that helps prevent the overlapping end boards from pulling loose where they overhang the edge: He glues the first and last three boards tightly together with marine epoxy. Then he cuts the tongue or groove on the termination..
HomeAdvisor's deck repair cost guide surveys homeowners to reveal the average price for repairing a deck, replacing deck boards and fixing deck railings. . In addition to removing and repairing areas with dry rot, you will need to figure out the root cause of the problem, including drainage and plumbing issues. If the area..
Home repair expert Henry Harrison shows a homeowner how to patch a bad section at the end of her porch slats
Whenever you're de-nailing wood it's a good idea to set up a comfortable work station. I like good solid sawhorses set at about crotch height. If I'm doing tongue and groove flooring or other material containing small nails I'll set the horses higher than this. The lower setting is great for heavy framing lumber..
First, a disclaimer: Make sure the wood you are going to use will stand up in the environment you're placing them in. You may be better off using these with the T&G on an indoor project. Weather outside will quickly weather non-pressure treated wood, and decks typically require thicker boards than you'd..
Pulling up tongue-and-groove flooring can be tedious and time-consuming -- more so when the boards are glued -- but it's not a test of carpentry skills. If you want to remove the boards safely, it's a good idea to give yourself lots of time, because you have to work methodically. That's also important if ..
Make the cut in a damaged board that's next to a good one and whose groove faces the other boards that will be replaced. (You can spot the tongues . Using a pry bar and hammer, remove the old wood on both sides of the cut, being careful not to harm the tongue of the undamaged deck board. Once the waste is clear,..